1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by admin

  1. admin
    Post

    Mimas V2 Configuration GUI

    Hi Ivan, Thanks for sharing this tool with the community and I apologize for delayed response. I personally believe the community will benefit...
    Post by: admin, Jul 5, 2017 in forum: FPGA Boards
  2. admin
    Post

    relay writeall ff\n\r does not work from pyserial and relay readall is not reliable

    Hello @rlegault, There were a couple of minor issues with the script (No \r after relay on/off commands and \r did not work as expected with...
    Post by: admin, Feb 27, 2017 in forum: Relay Modules
  3. admin
    Post

    USB 8 channel - gpio readall silent (possible since firmware 9)

    Hi Niclas, This was confirmed to be caused by a compiler related problem (potentially a compiler bug). We have shared V8 image over the...
    Post by: admin, Dec 15, 2016 in forum: GPIO Modules
  4. admin
    Post

    Displaying ADC Data on a Gauge

    Hi Brad, Once the data is available on a PC, serving that through web interface is simple conceptually. Run a web server and let the server read...
    Post by: admin, Oct 26, 2016 in forum: GPIO Modules
  5. admin
    Post

    Is there a practical limit on how many queries can be made of the GPIO?

    Hi Curtis, Our GPIO devices does not have any cycle limits as such other than the MTBF specified by the component manufacturers. Most components...
    Post by: admin, Oct 26, 2016 in forum: GPIO Modules
  6. admin
    Post

    Skoll - Kintex 7 Board

    Hi Ali, Writing DDR core is indeed difficult but using one doesn't have to be. Xilinx do offer DDR3 core for free and is bundled with Vivado....
    Post by: admin, Oct 26, 2016 in forum: FPGA Boards
  7. admin
    Post

    Can't program the Elbert V2 board

    Hi, This is most probably because the code that is programmed to be board pulling the clock input to low/high. Please follow the fix at the link...
    Post by: admin, Oct 26, 2016 in forum: FPGA Boards
  8. admin
    Post

    Is the Mimas v2 manual still available as pdf?

    Hi Ruben, The version 9 document is available at the link below and it is it is expected to stay there for some time. But new updates will always...
    Post by: admin, Oct 26, 2016 in forum: General Chit Chat
  9. admin
    Post

    Static assignment USB port

    Hi Discovery, It is not really possible to statically assign port names since it is up to the operating system to assign the name. And sometimes...
    Post by: admin, Oct 26, 2016 in forum: Relay Modules
  10. admin
    Post

    HID USB Bootloader

    Hi Niclas, Happy to hear that you were able to figure out the issue. In case of any further questions, please contact us anytime. Thanks, Tom...
    Post by: admin, Oct 19, 2016 in forum: GPIO Modules
  11. admin
    Post

    8 channel USB notify doesn't work

    Hi Ahmed, Notify is supported only on version 9 firmware and newer. You seem to have older version of firmware which does not support Notify...
    Post by: admin, Oct 19, 2016 in forum: GPIO Modules
  12. admin
    Post

    How fast can I toggle one output

    Hello Curtis, The only limit is the number of commands that can be sent to the device per second. There is no limit specific to toggling. I have...
    Post by: admin, Oct 19, 2016 in forum: GPIO Modules
  13. admin
    Post

    Is there a practical limit on how many queries can be made of the GPIO?

    Hello Curtis, Our USB GPIO devices can accept one outstanding command at any point of time (No command FIFO inside). The maximum number of...
    Post by: admin, Oct 19, 2016 in forum: GPIO Modules
  14. admin
    Post

    ADC reading frequency in 32 channel USB GPIO

    Sorry for the very very late reply, The recommended conversion rate is one conversion every 20 - 50ms or so. It can be faster but the rate...
    Post by: admin, Jul 28, 2016 in forum: GPIO Modules
  15. admin
    Post

    No /dev/ttyACMx with usbgpio16 on Linux

    dmesg should be available on most if not all distros. Thanks, Tom Nuamto Lab
    Post by: admin, Jul 28, 2016 in forum: GPIO Modules